router_a alex # smartctl -a /dev/sde smartctl version 5.38 [x86_64-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST3000DM001-9YN166 Serial Number: W1F06EB9 Firmware Version: CC9B User Capacity: 3,000,592,982,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Wed Mar 12 23:09:45 2014 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: ( 584) seconds. Offline data collection capabilities: (0x73) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x3081) SCT Status supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 084 084 006 Pre-fail Always - 135152976 3 Spin_Up_Time 0x0003 092 092 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 46 5 Reallocated_Sector_Ct 0x0033 090 090 036 Pre-fail Always - 13520 7 Seek_Error_Rate 0x000f 100 253 030 Pre-fail Always - 283678 9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 18853 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 46 183 Unknown_Attribute 0x0032 097 097 000 Old_age Always - 3 184 Unknown_Attribute 0x0032 001 001 099 Old_age Always FAILING_NOW 828 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 2044 188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 069 064 045 Old_age Always - 31 (Lifetime Min/Max 30/31) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 12 193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 796 194 Temperature_Celsius 0x0022 031 040 000 Old_age Always - 31 (0 16 0 0) 197 Current_Pending_Sector 0x0012 001 001 000 Old_age Always - 24888 198 Offline_Uncorrectable 0x0010 001 001 000 Old_age Offline - 24888 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 190048007883703 241 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 27320595633115 242 Unknown_Attribute 0x0000 100 253 000 Old_age Offline - 122980230355 SMART Error Log Version: 1 ATA Error Count: 23 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 occurred at disk power-on lifetime: 18852 hours (785 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 28 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 28 00 00 40 00 00:05:17.018 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:05:17.018 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:05:17.018 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:05:17.018 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 00:05:17.018 SET FEATURES [Set transfer mode] Error 22 occurred at disk power-on lifetime: 18852 hours (785 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 28 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 28 00 00 40 00 00:05:14.178 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:05:14.178 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:05:14.178 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:05:14.178 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 00:05:14.178 SET FEATURES [Set transfer mode] Error 21 occurred at disk power-on lifetime: 18852 hours (785 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 28 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 28 00 00 40 00 00:05:11.376 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:05:11.376 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:05:11.375 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:05:11.375 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 00:05:11.375 SET FEATURES [Set transfer mode] Error 20 occurred at disk power-on lifetime: 18852 hours (785 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 28 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 28 00 00 40 00 00:05:08.569 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:05:08.569 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:05:08.569 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:05:08.568 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 00:05:08.568 SET FEATURES [Set transfer mode] Error 19 occurred at disk power-on lifetime: 18852 hours (785 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 28 00 00 00 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 01 28 00 00 40 00 00:05:05.766 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 00:05:05.766 SET FEATURES [Reserved for Serial ATA] 27 00 00 00 00 00 e0 00 00:05:05.766 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 a0 00 00:05:05.766 IDENTIFY DEVICE ef 03 42 00 00 00 a0 00 00:05:05.766 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 18853 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.